Cosmetic ingredients

22/11/2026 9 min read

Hydroxypropyl methylcellulose (HPMC) in cosmetics: thermogelling

Hydroxypropyl methylcellulose thickens gels, cleansers and shampoos without carrying an electric charge, and, together with methylcellulose, it has a distinctive property: it thickens into a gel when heated and thins out again when cooled. For manufacturers, the points to manage are the gelation temperature, the effect of salts, how the powder is dispersed and the quality of each batch.

Hydroxypropyl methylcellulose (HPMC) in cosmetics: thermogelling
Close-up of an open cotton boll with four locks of white fiber — an illustrative image of plant cellulose, not depicting the specific raw material source of hydroxypropyl methylcellulose

Hydroxypropyl methylcellulose (INCI: Hydroxypropyl Methylcellulose, abbreviated HPMC; European Pharmacopoeia name: hypromellose) is a nonionic cellulose ether that dissolves in cold water to form a viscous solution; it is used to thicken, form films and stabilize dispersions in cosmetics, pharmaceuticals and food. Along with methylcellulose, HPMC has the characteristic of thickening into a gel when heated and returning to a solution when cooled (EFSA, 2018).

1. What is HPMC?

According to the E 464 food additive specification cited by the EFSA Panel (EFSA, 2018), HPMC is cellulose obtained from plant fibers, partially etherified with methyl groups and also carrying a small amount of 2-hydroxypropyl groups. The process is described as reacting alkali cellulose with a mixture of methyl chloride and propylene oxide. HPMC is therefore a chemically modified cellulose, not native cellulose in its original form.

As a polymer, HPMC has no fixed formula or molecular weight; CAS 9004-65-3. Grades differ in their degree of substitution and viscosity:

Parameter (E 464 specification, cited in EFSA 2018)Level
Methoxyl groups (–OCH3)19–30%
Hydroxypropoxyl groups3–12%
AppearanceGranular or fibrous powder, white, slightly yellowish or slightly grayish, odorless, tasteless, slightly hygroscopic
SolubilitySwells in water to form a viscous colloidal solution, clear to slightly cloudy; insoluble in ethanol
pH of a 1% solution5.0–8.0 (JECFA specification)
Propylene chlorohydrinMax. 0.1 mg/kg (EU); 1 mg/kg (JECFA)
LeadMax. 2 mg/kg

This is a food additive specification, not a legal requirement for cosmetic raw materials; use it as a reference point when reading a certificate of analysis (COA).

2. What does HPMC do in a formula?

  • Thickening and structuring the water phase. The Butter-C formulation handbook (chapter “Gels and gelling agents”) places HPMC among the cellulose ethers that thicken by chain entanglement, together with hydroxyethylcellulose (HEC) (in Vietnamese). EFSA notes that the viscosity of modified cellulose solutions depends on concentration, temperature, chain length and the presence of salts.
  • Nonionic. In the JECFA specification, HPMC solutions do not form a precipitate when copper sulfate or aluminum sulfate is added; this test is used to distinguish HPMC from sodium carboxymethylcellulose, i.e. cellulose gum (in Vietnamese), an anionic polymer.
  • Surface active. Also according to the JECFA specification, vigorously shaking a 0.1% HPMC solution produces a layer of foam. In a study of sodium dodecyl sulfate/HPMC foams (most of the authors belonged to the research division of a consumer goods company), HPMC entered the foam in the same proportion as in the initial solution and made the foam films thicker, which corresponded to more stable foam during the first 15–20 minutes (Perticaroli et al., 2020). This is a physicochemical study of a model system, not a test on a finished shampoo.
  • Film forming as water evaporates; film properties depend on the solvent and the plasticizer used with it.

3. Thermal gelation: a specific point to manage

EFSA describes methylcellulose and HPMC solutions as “insoluble when hot”: raising the temperature initially lowers the viscosity slightly; at the gelation temperature, the viscosity rises sharply; the process is reversible, and both the gelation temperature and the gel texture depend on the degree and type of substitution.

According to the literature summarized by Perez-Robles et al. (2022), at room temperature the loss modulus G″ of an HPMC solution is greater than its storage modulus G′ — meaning that an “HPMC gel” used at room temperature is essentially a thickened solution. On heating, G′ and G″ decrease, reach a minimum and then rise again until G′ exceeds G″; one recent explanation involves two steps: phase separation, after which the polymer-rich phase forms fibrils that interweave into a three-dimensional network.

Salts lower the gelation temperature. In concentrated solutions of low-molecular-weight HPMC, sodium chloride and calcium chloride lower the gelation temperature linearly with salt concentration, regardless of the charge (mono- or divalent) of the cation (Almeida et al., 2014, in vitro). Practical consequence: formulas with a high electrolyte content need stability testing at high temperature with the exact salt level intended.

Three manufacturing notes (based on the Butter-C handbook and practice):

  • Hot dispersion – cold dissolution: sprinkle the powder into a portion of hot water, in which HPMC does not dissolve so the particles stay separate, then add cold water and stir until clear; the specific temperatures follow the technical documentation for the exact grade. This avoids the “fish-eye” lumps common with cellulose ethers.
  • Measure viscosity at a fixed temperature, not while the sample is still warm after heating.
  • Hot filling or heating the finished product: only do this once the gelation temperature of the grade in use has been determined in the actual formula.

4. Evidence on skin: limited

The PubMed abstracts reviewed (November 2026) include no trial measuring a skin benefit of HPMC on its own in cosmetics: limited evidence. Most studies concern drug-loaded gels or film-forming solutions, evaluated in vitro or on pig skin — pharmaceutical formulation data. “Moisturizing” or “soothing” claims must be substantiated on the finished product.

5. Typical concentrations and product types

The quick reference table of the CIR (Cosmetic Ingredient Review, United States) Expert Panel (September 2017 update) lists “up to 4%” for HPMC in the limits column accompanying the “S” conclusion (based on the amended assessment of March 2009). Because “S” means safe in the present practices of use and concentration, this figure reflects the use level at the time of the assessment, not a recommended level; the table does not break it down by product type. The Butter-C handbook gives a working range of 0.3–2% for the cellulose ether group, to be validated in each formula.

Suitable product types: moisturizing gels, clear gels, cleansers, shampoos, personal lubricant gels. HPMC is found in cosmetics, pharmaceuticals and food, but the data from each field are not interchangeable:

ContextRoleSafety assessment (source)
CosmeticsThickening, film forming, stabilizingCIR: “S” — safe in the present practices of use and concentration (quick reference table, September 2020)
Food (E 464)Thickening, stabilizing, gellingEFSA 2018: no need for a numerical ADI, no safety concern at the reported use levels — dietary (oral) data
PharmaceuticalsCelluloses serve as excipients in tablets, capsules and gels (EFSA); HPMC is contained in preparations introduced into the eye during cataract surgery (Munk et al., 2013)Governed by the drug dossier, outside the scope of cosmetics

6. Safety: who should take care

CIR conclusion. The CIR quick reference table (September 2020) rates HPMC “S” (safe in the present practices of use and concentration), citing the original 1986 report (J Am Coll Toxicol 5(3):1-59) and the final report of March 2009. The full texts of these two reports could not be accessed through public links while this article was being written, so the article does not give detailed test data.

Dietary (oral) data. EFSA notes that celluloses are not absorbed, are excreted unchanged in the feces, have low acute toxicity and raise no genotoxicity concern. Do not use these data to claim “safe because it is edible” for cosmetics.

Immediate-type allergy: case reports exist, via the oral route or during surgery.

  • A 71-year-old person had severe anaphylaxis twice during cataract surgery; skin prick tests were positive for HPMC (contained in a preparation introduced into the eye) and for methylcellulose; at a later operation in which HPMC was avoided, there was no reaction (Munk et al., 2013).
  • A 47-year-old person developed urticaria and angioedema after ingesting products containing HPMC (a probiotic drink and digestive enzyme tablets); intradermal testing confirmed hypersensitivity to HPMC, and an oral challenge with HPMC caused urticaria (Lee et al., 2026).

Both are case reports, neither in the context of skin application. The article on cellulose gum (in Vietnamese) mentions a case report of cross-reactivity between cellulose derivatives.

Who should take care: people already diagnosed with an allergy to HPMC, methylcellulose or another cellulose derivative should consult an allergist, particularly about products used around the eyes, nasal sprays and throat sprays. Pregnant or breastfeeding women: there are not yet enough data specific to cosmetics; consult a doctor.

7. Perspective for brand owners (B2B)

  • ASEAN regulations: Hydroxypropyl Methylcellulose (also searched as “hypromellose”, “cellulose” and CAS 9004-65-3) is not listed in Annexes II, III, VI (version 2026-1, June 22, 2026) or VII (version 2025-2, December 12, 2025) of the ASEAN Cosmetic Directive; there is no specific concentration limit or label warning.
  • Reactants: propylene oxide (“Methyloxirane”, CAS 75-56-9, Annex II Ref 655) and methyl chloride (“Chloromethane”, CAS 74-87-3, Ref 1095) are substances prohibited as cosmetic ingredients. The E 464 specification controls the by-product propylene chlorohydrin. In practice: ask the supplier to confirm impurities, heavy metals and microbiology for each batch.
  • Labeling: INCI “Hydroxypropyl Methylcellulose”; “hypromellose” is the pharmacopoeial name. Hydroxypropylcellulose and Methylcellulose are different INCI names.
  • “Natural”: write “cellulose derivative”; avoid “completely natural”.
  • Changing grade: the degree and type of substitution affect the gelation temperature (EFSA); a change of grade or supplier requires retesting viscosity and thermal stability.
  • Microbiology: water-based gels need a preservative efficacy (challenge) test (in Vietnamese).

Butter-C can use HPMC in the contract manufacturing of gels, cleansers and shampoos; the raw material grade and the preservative system are finalized through testing in the formula.

Frequently asked questions

Are HPMC and hypromellose the same thing?

Yes. Hypromellose is the European Pharmacopoeia name; cosmetic labels use the INCI name Hydroxypropyl Methylcellulose.

Why does an HPMC gel change state when kept in a hot place?

Above the gelation temperature, an HPMC solution undergoes phase separation and then forms a gel network; salts lower this threshold. The phenomenon is reversible, but thermal stability testing is needed to choose a suitable grade and salt level.

How safe is HPMC in cosmetics?

CIR rates HPMC as safe in the present practices of use and concentration. Immediate-type allergy appears in case reports, via the oral route or when introduced into the eye during surgery, not on skin application.

Should I choose HPMC or HEC for a clear gel?

Both are nonionic. With HPMC, you also need to account for its surface activity (foaming when shaken) and its gelation when heated; choose by testing in the actual formula, including testing at high temperature.

Can pregnant women use it?

There are not yet enough data specific to topically applied cosmetics during pregnancy; consult a doctor.

References

  1. Cosmetic Ingredient Review. Quick Reference Table (September 2020) — Hydroxypropyl Methylcellulose entry. https://www.cir-safety.org/sites/default/files/qrt-fix_0.pdf
  2. Cosmetic Ingredient Review. Quick Reference Table (updated September 2017) — Hydroxypropyl Methylcellulose entry (amended). https://www.cir-safety.org/sites/default/files/safe-092017posted122017.pdf
  3. EFSA Panel on Food Additives and Nutrient Sources added to Food (ANS). Re-evaluation of celluloses E 460(i), E 460(ii), E 461, E 462, E 463, E 464, E 465, E 466, E 468 and E 469 as food additives. EFSA J. 2018. PMID 32625652
  4. Perez-Robles S et al. HPMC Hydrogel Formation Mechanisms Unveiled by the Evaluation of the Activation Energy. Polymers (Basel). 2022. PMID 35160624
  5. Almeida N et al. Phase behavior of concentrated hydroxypropyl methylcellulose solution in the presence of mono and divalent salt. Carbohydr Polym. 2014. PMID 24274553
  6. Perticaroli S et al. Multiscale Microstructure, Composition, and Stability of Surfactant/Polymer Foams. Langmuir. 2020. PMID 33232158
  7. Munk SJ et al. Two episodes of anaphylaxis following exposure to hydroxypropyl methylcellulose during cataract surgery. J Cataract Refract Surg. 2013. PMID 23571290
  8. Lee WJ et al. Hydroxypropyl methylcellulose-induced urticaria and angioedema: a case report. Allergy Asthma Clin Immunol. 2026. PMID 41792785

Get started

Talk to us about the product you plan to launch

Please send us your product direction and expected quantities. Our team will get back to you during business hours.

Công ty cổ phần Dược mỹ phẩm Butter-C · Business registration no. 0108681386 (Hanoi Department of Planning and Investment, 03/04/2019)
Head office: Huu Le village, Dai Thanh commune, Hanoi · Factory: Thanh Oai Industrial Cluster, Binh Minh commune, Hanoi, Vietnam
Hotline 0967 176 511 · [email protected] · privacy policy
Product catalog →